This maintenance chapter includes Service Info. Connect a charger and ammeter to the battery and start charging. Whats causing my week performance at high top speed? This chapter includes, System Components, Service Information, Trouble shooting, system Testing, Coolant Replacement, Thermostat, Radiator, Cooling fan, water pump and more. Fasten the generator lead and heater control switch lead on the wire harness with plastic bands. Apply a coarse lapping compound to the valve face.
Information found in the Lubrication System section is as follows: Lubrication System Diagram, Service Information, Troubleshooting, Oil Strainer, Pressure Relief Valve, Oil pump, Oil Cooler and more. Use only genuine Yamaha parts for all replacements. A shop manual is a reference tool and as in all s ervice manuals, the chapters are thumb tabbed for easy and fast navigation allowing you to find the exact service repair procedure's in the quickest time possible. Special tools may differ by shape and part number from country to country. . Loosen the locknut and adjusting bolt b.
Shaft Idle gear Washer Bolt Rotor assembly. Sheave holder 90890-01701 Primary clutch holder. Insufficient compression pressure will result in a loss of performance. If vertical movement is tight or rough, or if there is binding, check the spacer, bearings and frame pivot. Check the front arm side play by moving it from side to side.
Starter jet For assembly, reverse the disassembly procedure. Squeeze out the excess oil. Shift forks 1 and 2 Springs 1 and 2 Shift fork guide bar. The element should be wet but not dripping. Maintenance schedule, Fuel Line, Throttle Operation, Air cleaner, spark Plug, Spark Plugs, Valve Clearance, Decompressor System, Engine Oil, Engine Oil Filter, Transmission Oil, Engine Idle Speed, Radiator Coolant, Cooling System, Drive Chain, Drive Chain Slider, Brake Fluid, Brake Pads Wear, Brake Light, brake System, Skid Plate, Engine guard, Clutch System, Suspension, Spark Arrester, Nuts, Bolts, Fasteners, Wheels, Tires, Steering Head Bearing, Steering Shaft Holder Bearing, steering System and more.
My engine does not start. How do i set the Ignition Timing? It is very detailed and as complete as it gets with step by step procedures on how to maintain and fix your ride. Thermo switch 28 Nm 2. Radiator inlet hose Thermostat cover Thermostat For installation, reverse the removal procedure. Do not reuse the oil seal. It is not possible to include all the knowledge of a mechanic in one man- ual, so it is assumed that anyone who uses this book to perform maintenance and repairs on Yamaha machine has a basic understanding of the mechanical ideas and the procedures of machine repair.
Insert the couplers on the bracket of the front fender holder. Connect a charger and ammeter to the battery Set the charging voltage to 16 ~ 17 V. Fasten the parking brake cable with plastic bands. Important items are indexed at the end of the book. Route the rear brake hose through the guide on the swingarm.
Place the machine on a level surface. Direction Free play is decreased. Refer to the relative procedure in this manual for check, adjustment and replacement of parts. Coolant temperature Coolant temperature indicator indicator light comes light does not come on. Technical highlights of chapters include: Service Information, Troubleshooting, Removal, Installation, Dissassembly, Assembly, Inspection and more.
Cylinder gasket Dowel pin Piston pin clip Piston pin. Keep all parts away from any source of fire. A service repair manual doesn't become a simple guide for the mechanic but rather a essential tool of knowledge. Therefore, do not remove the radiator cap when the engine is hot. Before measuring the piston ring side clear- ance, eliminate any carbon deposits from the piston ring grooves and piston rings.
Start the engine, warm it up for several min- utes, and then turn it off. Loosen the locknut on the carburetor side. Fasten the front brake switch lead and front brake hose with plastic bands. Apply compressed air to the rear of the radi- ator. Main fuse The battery is not being charged. Hold the adjusting screw to prevent it from moving and tighten the locknut to specifica- tion. Fasten the rear brake hose and parking brake cable with plastic bands Route the parking brake cable through the guide on the swingarm.
Inner rotor Outer rotor Oil pump housing. Fasten the negative battery lead with plastic bands. Use only the appropriate special tools; this will help prevent damage caused by the use of inappropriate tools or improvised techniques. Place a receptacle under the transfer gear case. Loosen the locknuts tie-rod end of both tie-rods. Check: Minimum open-circuit voltage 1.