Pro cycle tach wiring. How to Wire a Sunpro Tach 2019-01-25

Pro cycle tach wiring Rating: 4,2/10 1905 reviews

Auto Meter® 19466

pro cycle tach wiring

It is useful for most Honda and other motorcycles, although some aftermarket additions may cause fitment issues. I think this is the instruction sheet you need:. Apply power to the tachometer by attaching the power input wire of the tachometer to the 12-volt dashboard lighting supply of the car. The shift light cannot be set if the engine is running. All implied warranties shall be limited in duration to the said 12 month warranty period.

Next

How to Install a Tachometer: 8 Steps (with Pictures)

pro cycle tach wiring

Attach the tachometer backlighting wire. Locate the output wire from your distributor. If your car doesn't have one, it's a good way to keep an eye on your engine speed. The tach pointer may not always rest at zero, this is normal. If a headlight or number plate spacer is present, there should be plenty of room. This helps the driver monitor the vehicle and shift gears at the optimum times. I'm hoping the tach isn't dead but wanted to check with y'all to see if there's a wiring trick to making this work? It's a good idea to install a rubber grommet where the wire s pass through the firewall as part of your installation.

Next

Autometer Pro Cycle Tach help

pro cycle tach wiring

This warranty is limited to the repair or replacement of parts in the Auto Meter instrument and the necessary labor done by Auto Meter to effect the repair or replacement of the Auto Meter instrument. On my 240 I used a piggy-back connector onto the instrument light rheostat. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Taking the highly precise circuits from the individual speedometer and tach and combining them into one unit gives you the accuracy and the response time you need and the convenience of a one piece solution. Connect the tach lead to that wire. Founded in 1957 by electronic instrumentation pioneer Vern Westberg, today the company is a division of the Harbour Group. This warranty applies only to the original purchaser of product and is non-transferable.

Next

Tachometer Hookup Instructions

pro cycle tach wiring

Before you mount it in the steering column, it's a good idea to hook up the wiring and and test it out while you rev the engine, to make sure it works. The tachometer wire must be fed through a grommet in the passenger compartment to reach the engine compartment. This warranty applies only to the original purchaser of product and is non-transferable. Standalone gauges and bagger kits are offered to make it easy to add Pro-Cycle gauges to your ride. A Scotch lock should be used to lock up your whisky cabinet-lol. It's important to make sure you've got the correct wire for the tachometer, which means you might need to use a multimeter with a tach setting to test the wires correctly, and consult the shop manual for your engine. Warranty claims to Auto Meter Gauge Works must be transportation prepaid and accompanied with proof of purchase.

Next

Auto Meter® 19466

pro cycle tach wiring

Calibration All model except Model 19233 Your Pro-Cycle tachometer is calibrated for 1 and 2 pulses per revolution Do not confuse with single and dual fire. This article has also been viewed 221,470 times. Worst case, I just re-install the stock tach that works just fine. Choose a mounting location for the tachometer. Improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty.

Next

Tachometer Hookup Instructions

pro cycle tach wiring

Connect the white wire to the instrument panel lighting circuit connected to the dimmer control switch. Sunpro is a maker of gauges and tachometers, and has been producing these devices since 1935. Also: Connect the 12V wire to fuse 13 so the ignition key will switch it on and off. The brown wire must be cut. When engine is started, pointer will position on the correct rpm. Locate the 12-volt switched dash lighting supply for the dashboard on the car fuse box. Compatible with nearly any factory speed sender and 1-12 cylinder applications, this unit is simple to calibrate and designed with the type of durability you expect in an AutoMeter gauge.

Next

Autometer Basic Tach Installation Wiring Instructions Tutorial How

pro cycle tach wiring

Bolts between the lower bar clamps and triple clamp plate with 100-106mm bolt spacing. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. If the partnership between Auto Meter and Gauge Works dissolves, then all warranty adjustments will be covered by the Gauge Works Co. Three Year Limited Warranty applies only to Pods, Cages and Pillars Gauge Works warrants to the consumer that all Auto Meter Gauge Works products will be free from defects in material and workmanship. There tachometers except model 19208 are water resistant on the face only.

Next

PRO

pro cycle tach wiring

See Step 1 for more information. In a 6 cylinder engine, most of the time the 2 switch should be up and the 1 should be down. Solid core ignition wires may cause tach interference. Avoid positive side of coil for green wire. Tachometer wiring should be run inside insulated housing. This includes normal washing, even moderate pressure washing.

Next