S Store unit with all guards in place. Please read and retain this manual. Check controls to be sure they are functioning properly. Be sure that all nuts, bolts, screws, and pins are securely 4. Raise upper handle to the operating position and tighten handle knobs securely. S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.
To avoid severe burns on contact, stay away from these areas. Spark plug wire is 8. West Mississauga, Ontario L5V 0B4 Giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased. Push the upper vacuum tube into the vacuum inlet. Use up fuel left in carburetor by starting engine and letting it run until it stops. Always be sure of your footing, and keep a firm hold on the handles.
Remove ice and snow on and around fuel tank cap. The machine is equipped with a two-stroke fully sythetic air cooled two stroke oil at a mixture of engine and must always be run using a mixture of 1:50 2% gasoline and two-stroke engine oil. When using your unit as a blower, always install blower tubes. Run the machine a few minutes after throwing snow weights, counterweights, or cabs. Long-term exposure to noise can result in permanent hearing Note the following before starting:. D Check air intake opening, blower tubes, vacuum tubes, and elbow tube frequently, always with engine stopped and spark plug disconnected. Secure with retainer in drive control bracket.
The instructions will enable you to assemble and maintain your snow thrower properly. Use to secure upper handle to lower handle. These symbols may appear on your snow thrower or in literature supplied with the product. Safety ignition key - must be inserted for the engine to Traction drive control lever - used to engage power-pro-start and run. S To reduce the risk of hearing loss associated with sound level s , hearing protection is required. Never operate the machine at high transport speeds on slippery surfaces.
Breathing exhaust fumes can kill. Insert rod into speed control bracket and secure with retainer spring. Auger control lever - used to engage auger motion throwRecoil auxiliary starter handle - used for starting engine. If the deflector becomes damaged, it shouldbe replaced. Keep loose hair, loose clothing, fingers, and all other parts of the body away from openings and moving parts. Keep the area of operation clear of all persons, par- 5.
What is what on the b lower? S Vacuum Bag --Do not use vacuum bag if it is torn or damaged. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow. Use of non-compliant replacement parts is a violation of federal law. D To avoid static electricity discharge, do not wear rubber gloves or any other insulated gloves while operating unit. Contact an authorized service dealer. Know how to stop the device.
Prime as instructed in the Operation section of this manual. Be sure lever springs back and locks into desired position. Check for dirty fuel filter; replace. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. This could require pulling the starter handle many times, depending on how badly the unit is flooded.
We have competent, well-trained technicians and the proper tools to service or repair this unit. Hold the vacuum inlet cover open until upper vacuum tube is installed. Muffler Cover Spark Arresting Screen Hood Screws Replace the spark arresting screen every 50 hours of operation or if any damage or breaks in the screen are noted. Skid plate - used to adjust height of scraper bar from the ground. Place wire where it cannot come 1. Cut down all four corners of carton and lay panels flat.
Debris such as gravel, sand, dust, grass, etc. Clean the outside of your snow thrower after each use. Place wire where it cannot comeand should be replaced by original equipment manufacturer in contact with spark plug. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Failure to do so is a violation of the law. D Never run unit without the proper equipment attached. Adjust speed until engine runs without stalling idle speed too slow.
Do not safety glasses or eye shields while operating use to start a warm engine. The engine on your snow thrower has been shipped, fromSkid plates are located on each side of the auger housing the factory, already filled with oil. Also, alcohol blended cover that does not retain moisture. The toolbox islocated on top of the belt cover. Install clutch rod in swing plate; secure with hairpin.