Install the connector with its lead side facing inward. Cooling Reserve Tank Hose Run the hose inside the under ring. Such a shock to their parts can damage them. Special Tool - Hand Tester: 57001-1394 Injector Resistance Connections to Injector. If the fan does not rotate, inspect the following. Main Throttle Sensor Signal 28.
Wait until the muffler cool down. Special Tool - Hand Tester: 57001—1394 Injector Resistance Connections to Injector. Then tighten them according to the specified se- quence to prevent case warpage or deformation which can lead to malfunction. Avoid sharp bending, kinking, flattening or twisting. Also, the throttle valve may not open fully at full throttle. Before replacing a blown fuse, always check the amperage in the affected circuit. Replace or repair any defective parts, if necessary.
Side Stand Switch Lead 4. Sealant - Kawasaki Bond Silicone Sealant : 92104-0004. Wheelbase 1 425 mm 56. If the separator has any cracks or damage, replace it with a new one. Toothed Washer, 31 mm 1. Also, check to see that each cotter pin is in place and in good condition.
United States and Canadian Models. To Cylinder G: Apply grease. Battery 12 V 8 Ah C. The radiator fan may start even if the ignition switch is off. Tighten the bolt to the specified torque with the stopper for turning prevention applied. Inlet Air Pressure Sensor 13.
If the frame is bent, dented, cracked, or warped, replace it. Fuel injector trouble Inspect see chapter 3. The plug may also be cleaned using a high-flash point solvent and a wire brush or other suitable tool. Run the brake hose through the inside of the reservoir hose. The headlight comes on after the starter button is released and stays on until the ignition switch is turned off. They are specifically written for the do-it-yourselfer as well as the experienced mechanic.
Therefore the cutter must not be used for other purposes than seat repair. Description : You are buying a pdf service shop manual for a kawasaki z750 zr 750cc 2004 you will receive this pdf file emailed to your paypal email address within 4 hours of your purchase if you would like the same pdf service manual shipped to you on a dvd please pay the 499 shipping charge during checkout. If whitish cotton-like wafts are observed, aluminum parts in the cooling system are corroded. Such a shock to the sensor can damage it. Overall Height 1 180 mm 46.
This is to set the screw to its original position. If any journal has worn past the service limit, replace the crankshaft with a new one. The push rod does not return to its original position once it moves out to take up camshaft chain slack. Torque - Rocker Arm Nut: 34 N·m 3. The subthrottle valve is built in the each throttle body. Place blocks under the wheel so that the disc does not touch the ground. Ball Bearing and Needle Bearing Do not remove pressed ball or needle unless removal is absolutely necessary.
Avoid sharp bending, kinking, flattening or twisting. If the teeth are worn as illustrated, replace the sprocket, and inspect the drive chain wear see Drive Chain Wear Inspection. Front Left Turn Signal 15. Electric Starter Button Signal 4. If the measured journal diameters are not less than the service limit, but do not coincide with the original diameter markings on the crankshaft, make new marks on it.
If the connector is corroded or dirty, clean it carefully. Crankshaft Sensor and Oil Pressure Switch Lead Run the lead inner side the starter lead. Set the cover to cover all of the connector. Forcibly prying off the seat cap to add water is very dangerous. Air Cleaner Drain Hose 4. .
. Starter Clutch Oil Passage Hole 4. Main Fuse 30 A G. Run the main harness through lower and right side of the thermostat. Friction and steel plate warp. Ignition Fuse 10 A nostic System Connector 6. Fan Fuse 15 A 2.