Hyd mech h 14a manual. Fabricating Equipment Inc:Band Saws:Hyd 2019-02-17

Hyd mech h 14a manual Rating: 4,9/10 1210 reviews

Hyd

hyd mech h 14a manual

Save money with its split front vise, where the material is clamped on both sides of the saw blade. This reduces the breakaway burr and improves the surface finish of the cut. With an enclosed design for superior safety, this machine uses 66% less energy than competing models due to on-demand hydraulics which only operate when needed. Our Service Department will keep your saw in motion. Designed for high production cutting with a carbide tipped blade, the H-14A is unlike anything on the market.

Next

x HYDMECH H

hyd mech h 14a manual

If the alarm or fault code persists, check the led screen on the blade motor inverter drive for the presence of an error code, call the factory with the saw serial number, inverter model number and the error code. A large selection of bi-metal, grit and carbide tipped bandsaw blades as well as Fluid and Drip Lubricants. With an enclosed design for superior safety, this machine uses 66% less energy than competing models due to on-demand hydraulics which only operate when needed. Reverse any two of the three phase wires supplying power to the saw. On my inverter driven machine the blade shuts down and will not restart.

Next

Fabricating Equipment Inc:Band Saws:Hyd

hyd mech h 14a manual

A touch screen controller operates the automatic cycle and allows for manual operation. This provides proper positioning of the guide arm spacing, in relation to material width, at all times. The chip auger may be jammed with a thin piece of metal. This reduces the breakaway burr and improves the surface finish of the cut. Blade speed is easily adjusted from the control console and a wide range of available band speeds allows for a clean cut across many types of material.

Next

Fabricating Equipment Inc:Band Saws:Hyd

hyd mech h 14a manual

A cast iron guide arm mechanically connected to the front vise movable jaw provides proper guide arm spacing to fit the material being cut. Inspect the coupling to see if one of the flanges has loosened and slid apart. This material is for reference purposes only; please contact our with any questions or concerns. My chip auger has stopped turning on my saw. Save money with its split front vise, where the material is clamped on both sides of the saw blade. Designed for high production cutting with a carbide tipped blade, the H-14A is unlike anything on the market.

Next

2010 Hyd

hyd mech h 14a manual

The H-14A has a heavy-duty shuttle vise powered by a ball screw and vector motor. Its 25 mm remnant length option reduce material waste saving you money! With an enclosed design for superior safety, this machine uses 66% less energy than competing models due to on-demand hydraulics which only operate when needed. Save money with its split front vise, where the material is clamped on both sides of the saw blade. We carry complete lines of replacement blades, aftermarket parts and blade coolant. My saw runs, but I have no hydraulic functions or any pressure showing on the system pressure gauge.

Next

HYDMECH Horizontal Band Saw

hyd mech h 14a manual

Filters should be changed after the first 50 hours of operation and then every 500 working hours after that. A cast iron guide arm mechanically connected to the front vise movable jaw provides proper guide arm spacing to fit the material being cut. Designed for high production cutting with a carbide tipped blade, the H-14A is unlike anything on the market. Look into one of our maintenance contracts to ensure quality and optimal service for all your machine fabrication needs. If it is necessary to re-connect the coupling, use removable Loc-Tite on the set screws, or if the coupling is damaged, it will need to be replaced. Between the hydraulic pump and motor there is a bell housing containing a three-piece coupling. Lower the head fully down, shut off the hydraulics, and reverse the two conveyor hoses at the hydraulic manifold.

Next

NEW x HYD

hyd mech h 14a manual

If you discover any inconsistencies on our website please. Then put the hoses back as they were initially. If you are unable to locate or remove the obstruction, you need to reverse the auger rotation. A touch screen controller operates the automatic cycle and allows for manual operation. Its 25 mm remnant length option reduce material waste saving you money! Hydraulic saw guides are set automatically. For absolute accuracy, please consult the products specification. We've included several resources and troubleshooting guides below.

Next

2010 Hyd

hyd mech h 14a manual

The cast iron side guide arm is mechanically connected to the front vise movable. A cast iron guide arm mechanically connected to the front vise movable jaw provides proper guide arm spacing to fit the material being cut. Need a Price Quote or More Information? With new saw installations, if there is no pressure showing on the system pressure gauge, it is likely that the phase wiring is backwards. Disconnect the supply voltage to the saw for approximately five minutes. Its 25 mm remnant length option reduce material waste saving you money! When calling to order filters, please refer to the information listed on your current filter to obtain the proper dimensions as different sizes are used.

Next

2010 Hyd

hyd mech h 14a manual

We can ship and deliver to your shop. Start the hydraulics, raise the head, and switch the head to the down position and the chip conveyor will run in reverse dislodging the piece of metal. . This reduces the breakaway burr and improves the surface finish of the cut. A touch screen controller operates the automatic cycle and allows for manual operation. Turn the power back on and try to restart the saw blade. This is a fully automatic band saw with hydraulic full stroke vises.

Next

2010 Hyd

hyd mech h 14a manual

. . . . .

Next