Cpi indico 100 service manual. Indico IQ Installation Chapter 1C 2019-02-14

Cpi indico 100 service manual Rating: 8,1/10 1724 reviews

Del Medical Technical Support

cpi indico 100 service manual

A supply of connectors for wiring: terminal lugs, caps, splices etc. An end user may get this E if the technique selection is above or below operating parameter of the tube. X-Ray Generator Service Manual Supplement 746026 Rev. Check J8 on the rotor control for proper tube selection. A minimum of 42 inches 1.

Next

Del Medical Technical Support

cpi indico 100 service manual

Preparing for Installation 1C 1C. The console is convection-coded, and the main cabinet is fan cooled. Reference notes are provided at the end of Table 2. Swap the cable with a standard network cable as a test. It may be anchored if necessary. Answer: GenWare has well over 240 tube types in its library.

Next

CPI Indico 100 50 kW X

cpi indico 100 service manual

Please see note 9 before attempting to use this Dual Speed Starter configuration. On the right side of the display select clock, then select the function that you want to change by rotating the knob in the direction that gives you what you wanted to change then press Exit soft key to exit the program. The main resistance is about half the phase resistance with a typical R stator. X-Ray Generator Service Manual Supplement 746026 Rev. This is primarily due to a mA overload condition usually caused by arcing in the secondary Hv xfmr, Tube or hv cables or gross mis-calibration of the filament. For example, if the tube that is being installed is not in the consoles tube library, GenWare will need to be used to load the tube data into the console. This jumper tells the rotor control pcb what tube is being used so the proper rotor current can be sampled during the prep process.

Next

Del Medical Technical Support

cpi indico 100 service manual

The Low Speed Starter is integrated into the H. Capacitor selection is made automatically by relays located on the Dual Speed Starter. Answer: Most commonly on new installs, a jumper on the rotor control pcb is mis-set. This problem is known to occur during new installations especially if the comm. Device for measuring true kVp. This problem is known to occur during new installations especially if the comm.

Next

Del Medical Technical Support

cpi indico 100 service manual

Preparing for Installation 1C 1C. Answer: In order to clear this error you must reload the generator defaults. These should be large enough to allow the cables to be routed without risk of damage. The Low Speed Starter part number corresponds to the value of phase-shift capacitors installed. Connect the grid connection to Ground when using these tubes, and select the insert type within the Generator software corresponding to the equivalent non-grid tube. When ordering a new rotor board, the part off the board will be helpful. Test phantoms to verify the imaging systems if applicable with the generator.

Next

CPI Indico 100 50 kW X

cpi indico 100 service manual

This procedure is a simple one and can be found in chapter 3, programming the generator. The customer has to provide the hardware required to secure the generator to the floor. The installer must verify correct low speed operation if these alternate Dual Speed Starters is used. By default, this starter is typically factory set to the 28 μF position. The housing number is usually not shown on the identification label. X-Ray Generator Service Manual Supplement 746026 Rev.

Next

Del Medical Technical Support

cpi indico 100 service manual

However, there are some instances where it will need to be used. A strobe or reed type tachometer to verify that the anode is rotating up to speed. Check that the washers under the keps nut are not caught between the dual speed starter board mounting plate and the generator chassis. X-Ray Generator Service Manual Supplement 746026 Rev. This is only available with one-tube generators. For 2-tube systems using different tube types, both tube types must be considered. Answer: The mA fault calibration needs to be performed; The actual filament reference voltage cannot exceed the limit set in calibration.

Next

Del Medical Technical Support

cpi indico 100 service manual

The installer must confirm the stator type for the planned tube s. X-Ray Generator Service Manual Supplement 746026 Rev. Answer: Sure Prep was made standard on later models to allow prep hold for approximately 1 minute. Refer to Generator manuals section for kV Fault troubleshooting guides. This information can also be found in the service manual under proper grounding.

Next